Primary:      0478 535 743

Secondary:   0478 535 745

 

Categories Categories

12V-48V DC Speed Control 50A External (Case Model)
12V-48V DC Speed Control 50A External (Case Model) 12V-48V DC Speed Control 50A External (Case Model) 12V-48V DC Speed Control 50A External (Case Model) 12V-48V DC Speed Control 50A External (Case Model) hall effect devices

12V-48V DC Speed Control 50A External (Case Model)

$97.96 (Includes GST)
Weight: 0.5 kg
SPCU10070
Out of stock
 
50A DC Motor Control External Case Model
For Hall Effect Throttle Information, Please visit the throttle page to see the models we have available


This is an overhaul of the previous reliable controller to give it better efficiency, current control with higher burst and spiking capacitiy. This model is the External cased version of the PCB model. It is supplied as a fully assembled, ready to go unit. There's no assembly required everything is ready to go out of the box!

It's a high quality device, that you can use over multiple applications for many years. Being all genuine components, you can be sure of a long life, not a unit that you only get to use once because it blew up. The series II was built to expand on the ranges of motors that customers typically tend to use on these controllers.

High Power Design!
Simply, one of the best value units available on the market in its price range! Has features found only on controllers 2-3 times more expensive!
Lovingly hand assembled in Australia

Features:

  • 12V-48V Input Voltage (Battery Bank) 12V-55V (Regulated Power Supply ONLY!)
  • High Quality Aluminum casing!
  • 0-100% Speed Regulation!
  • Constant torque with Pulse Width Modulation (PWM)
  • High Quality Industrial Design
  • Efficient High Voltage Regulator
  • On/Off Switch (Built in!)
  • 3 Soft start settings (Off, Slow, Slower) ramps up to the desired speed once the controller is switched on, and unlike cheap controllers every time you switch it off and on (using the switch) it will ramp up to speed again!
  • Max Current up to 50A (for SHORT periods)
  • 40A Continuous current 
  • 2 Oz Double Sided PCB
  • High Speed Mosfet driver averaging 1.6uS opening/closing times
  • High Current 180A Mosfets with worlds lowest RDS On in TO-220!
  • Low Battery Voltage cut-out (for 12V, 24V and 36V)
  • Adjustable Frequency From 300Hz to 25Khz
  • Can work with Hall Effect Throttles (Model Dependent)
  • Over voltage Protected, ESD Protected!
  • Filtering, Clamping & Snubber Protection Included
  • Adjustable Start Positioning for Hall effect and Potentiometer setups
  • 8 Way Terminal Block For simple connections
  • External connectors for Hall Effect or Potentiometer, so you can make your own cable lengths up to 5m!
  • Passive cooling! No fans to break down or sieze up!!
  • Highly Configurable!
  • Potentiometer, Hall effect throttle or Hall Effect Foot throttle options!
  • Suitable for use Power supplies (doesn't feed power back into the source)
We shouldn't even have to say this but Please be AWARE of the current your motor draws. We've seen (and even sell) some motors that can be overdriven. To give an example, a motor may be rated at 450W at 24V which should use about 24A, but when you power it up and have it under HEAVY loading, the current draw can go as high as 150A!
ALso, please be aware of the voltages your motor can generate!
Putting a high power motor on this controller and then trying to overdrive it is a BAD idea!, the supression diode in this controller can handle up to 1200v from the motor but if you have the above setup then the motor being an inductor can generate incredibly high voltages which then feed BACK into the controller!
So you may need to add a snubber to your motor in these cases to drop the high voltages! 
Setting up and Using your new controller!
Simply download the instructions on the 'Attachments' page !
 

Speed control Manual (25A-50A_Speed_Control_DOX101.pdf, 184 Kb) [Download]